← All postsPerson using RMD Calculator on a laptop for a real retirement distribution planning task

Work Out Your 2026 RMD With Real Numbers, Step by Step

Estimate a US required minimum distribution from birth year and 12/31 balance, with a first-year delay example and common slip-ups.

RMD calculatorrequired minimum distributiontraditional IRAretirement withdrawalsuniform lifetime tableretirement planningfinance calculatorsUS retirement
5 min readFinance, Tax & Retirement

If you hold a traditional IRA in the United States, the government eventually insists you start taking money out, and the arithmetic is simpler than most people expect. RMD Calculator takes your birth year, the distribution year and your prior year-end balance, then divides by the IRS divisor for your age. This guide walks through three people with different birth years so you can see where the answer changes.

The calculation here is for US account owners under the Uniform Lifetime Table, and it is an estimate for planning, not tax advice. The clip below shows the calculator in use.

Calculate a required minimum distribution

Calculate a required minimum distribution

The formula in one line

Required minimum distribution equals the account balance on December 31 of the previous year, divided by a divisor that depends on the age you reach during the distribution year. The divisor comes from the IRS Uniform Lifetime Table in force since 2022. A few entries show the pattern: 26.5 at age 73, 25.5 at 74, 24.6 at 75, 22.0 at 78 and 20.2 at 80. The divisor shrinks every year, so the same balance produces a larger required withdrawal as you age.

Two inputs trip people up. The balance is the statement figure from last year's December 31, not today's value, so a market swing this autumn does not change the 2026 number. And "age" means the age you turn during the year, which the tool works out as the distribution year minus your birth year.

Example one: born 1953, first RMD year

Dana was born in 1953 and turns 73 in 2026. Her traditional IRA stood at $412,600 on December 31, 2025. In the tool she enters 1953, 2026 and 412600. The starting age for her birth year is 73, so the page shows a required amount.

Divisor 26.5 gives $412,600 / 26.5 = $15,569.81. The page also shows about $1,297 a month, which is only that figure divided by twelve, useful for budgeting but not a rule that you must withdraw monthly. She can take it in one go or in pieces, as long as the total for the year is met.

Because 2026 is her first RMD year, the tool adds a note: she may delay the first distribution until April 1 of the following year.

The delay trap: two RMDs in one tax year

Delaying looks like a favour, but it stacks income. If Dana waits, she still owes the 2026 amount of $15,569.81 by April 1, 2027, and then the 2027 amount by December 31, 2027. For 2027 she is 74, the divisor is 25.5, and the balance used is her December 31, 2026 figure. Suppose that is $438,900. Then $438,900 / 25.5 = $17,211.76, and the 2027 tax year would carry $15,569.81 plus $17,211.76, a total of $32,781.57 of required withdrawals.

To check this in the tool, set the distribution year to 2027 and enter the new balance. The year box accepts 2022 up to next calendar year. Whether the delay saves tax depends on your other income that year, which is a question for your tax preparer. The income tax calculator helps you see how a larger taxable year might look before you decide.

Example two: born 1960, no RMD yet

For anyone born in 1960 or later, the starting age is 75. Enter birth year 1960 and distribution year 2026 and the tool does not show an amount, because that person is 66. Instead it explains that no distribution is required yet and shows a what-if figure for the starting age. This is a quick way to sketch the future: put your expected balance in and see what a 75-year-old would owe on it. Treat the what-if as a rough scale, since your real balance in nine years will differ.

Example three: born 1948, a later-age check

Someone born in 1948 turns 78 in 2026. With $250,000 on December 31, 2025 and a divisor of 22.0, the calculation gives $250,000 / 22.0 = $11,363.64. People in this group sometimes forget that the required fraction keeps growing, so the percentage withdrawn is 4.5 percent here, compared with about 3.8 percent for Dana at 73. That is the divisor table doing its job.

Steps in the tool

  1. Enter your birth year. The tool rejects anything before 1900 or after the current year.
  2. Enter the year the distribution is for.
  3. Enter the account balance as of December 31 of the year before.
  4. Read the result: required amount, the divisor used, and the approximate monthly figure.
  5. If you see a "no required distribution yet" message, note the starting age it quotes for your birth year.

If you have several traditional IRAs, add their December 31 balances together and enter the total; the IRS lets you total the IRA amounts and take the withdrawal from any of them. Workplace plans are different: a 401(k) or 403(b) generally has its own calculation per plan. Check IRS Publication 590-B for the exact aggregation rules for your account types.

What this calculator does not cover

  • Roth IRAs have no required distributions for the original owner, and the tool simply divides whatever balance you type, so do not enter a Roth balance.
  • A spouse more than 10 years younger who is the sole beneficiary can qualify for a different table, which gives a smaller number. The page points to IRS Publication 590-B for it.
  • Inherited accounts follow separate rules, including a 10-year schedule for many beneficiaries.
  • Still working? A current employer's plan can have its own rule for non-owners, so confirm with your plan administrator.
  • Missing a required amount carries an excise tax, which SECURE 2.0 reduced to 25 percent of the shortfall, and 10 percent if corrected promptly. Confirm current figures with the IRS.

Mistakes to avoid

Using today's balance instead of last December 31. Entering a birth year in the wrong decade and being told you are under the starting age. Treating the monthly figure as a requirement. Forgetting to rerun the numbers each January when the new statement arrives. And relying on one estimate for a decision with tax consequences; confirm with the custodian, who reports the official figure.

Related planning pieces sit nearby. The Social Security calculator shows how benefits fit into the same retirement years, and the 401(k) calculator covers the saving side. For an overview of how these calculators fit together, see the guide on retirement calculators explained, or browse all finance calculators.

This is general information using the IRS Uniform Lifetime Table in effect since 2022 and is not tax or investment advice; your custodian and a qualified adviser have the final word on your exact amount.

Which part of the RMD rules still feels unclear: the first-year delay, multiple accounts, or the beneficiary tables? Tell us on the contact page.

Open RMD CalculatorOpen Income Tax CalculatorOpen Social Security CalculatorOpen 401(k) Calculator