← All postsNarrator at a home desk with headphones reviewing an audio waveform after noise reduction

Cut HVAC Hum From a Home-Office Voiceover Take

Reduce steady air-conditioner or fan noise in a narration file, choose between four cleanup levels, and avoid the watery over-processed sound.

noise removerHVAC humvoiceover cleanupbackground noisehome studioaudio editingaudio toolsbrowser tools
4 min readAudio Tools

The take was good: steady pacing, no stumbles, the right emphasis on the product name. Then you put on headphones and hear it, a low roar underneath every sentence that disappears only when you stop talking. In a home office that is usually the air conditioner or a furnace fan. Background Noise Remover is built for exactly this kind of constant noise: hum, hiss and fan sound that stays at roughly the same level.

The clip below shows the upload, level choice and download.

How to Remove Background Noise from Audio Online

How to Remove Background Noise from Audio Online

What the tool is good at, and what it is not

It uses spectral subtraction: it measures the noise in your own file and subtracts that pattern from the whole recording. That works well on a steady noise floor and poorly on a busy, changing scene such as a crowded room or a conversation with traffic and dishes. A separate fourth level, Voice, applies a small noise-suppression model for speech, which copes better when the noise changes. More on that below.

Be honest with yourself about the source. Cleanup reduces noise; it cannot rebuild a voice recorded far from the microphone, and strong settings take some of the voice's body along with the noise.

What the four levels change

For each file the tool first listens for the quietest stretches, averaging the quietest quarter of short 50 millisecond windows, and treats that as the noise floor. Suppose your narration measures -52 dB. The three standard levels then work like this:

  • Light removes up to 12 dB of noise and treats sound within 8 dB above the floor as noise, so the filter is aimed at -44 dB.
  • Standard removes up to 20 dB and counts sound up to 13 dB above the floor, aimed at -39 dB.
  • Aggressive removes up to 35 dB and counts sound up to 20 dB above the floor, aimed at -32 dB.

So the same file is tuned differently from a quieter room's file, because the target moves with the measured floor. Higher levels clean more but risk a dull, underwater voice.

A worked pass on a 3-minute narration

Say you recorded a three-minute voiceover with the air conditioning cycling and a steady hiss beneath it. Open the tool, drop the file and wait for the file name to appear. If a size notice shows, the file is over your plan's limit and Remove Noise stays disabled; trim it first with Audio Trimmer.

  1. Pick Light and click Remove Noise. Listen to the preview, especially the pauses between sentences.
  2. If the hum is still plainly audible, go to Standard and run again. Changing the level clears the old result, so you compare by listening, not by stacking passes.
  3. Use Aggressive only if the voice stays natural. A thin recording usually does not survive it.
  4. If the noise is not constant, such as a fan that switches on mid-take, try Voice instead.
  5. Download. The file is named denoised_ plus your original name, in the same format family as the original.

When the process is done, a line under the player reports roughly how much quieter the pauses became, for example about 18 dB in the quietest parts. It measures the gaps, not the speech, so treat it as an indication, not a promise. If it reports little noise to remove, the recording was already clean or the noise is not steady.

When to choose Voice

Voice is meant for speech with changing background sound: a fan that cycles, traffic passing, a keyboard being tapped. It loads a small voice model from this site on first use, so the first run takes a moment longer. It is not suitable for music, where it can damage the sound, so do not run a song or a musical bed through it.

Many voiceover artists try Standard first, since it is gentler on tone, then fall back to Voice if the noise moves. If both leave a watery quality, the better answer is a re-record in a quieter space, even with a blanket over the microphone, rather than a harder setting.

Habits that make cleanup work better

  • Leave two or three seconds of room tone at the start. The tool looks for quiet stretches, and a clean pause helps it judge the noise level.
  • Record with the HVAC off if you can, then run the cleanup only for the takes where you could not.
  • Keep the microphone close, a hand's width or two from your mouth. The closer the voice, the further it sits above the noise, so you can often use a gentler level.
  • Work from the original recording, not a file that was already compressed several times.

Common mistakes

  • Starting at Aggressive. Move up only as far as needed; each step trades voice for quiet.
  • Running the result through again. Cleaning an already-cleaned file raises the odds of a robotic or watery tone.
  • Using it on music or on a recording with two people over a loud room. Those are outside what spectral subtraction does well.
  • Judging by the dB figure alone. Listen on headphones and on laptop speakers.
  • Forgetting the level afterwards. Noise reduction can leave a quieter file; a pass through Audio Normalizer brings it back to a consistent loudness.

Where it fits in a voiceover job

If your take is inside a video file, Extract Audio pulls the sound out first so you can clean it separately. After cleanup, trim the pauses and the false starts, then normalise. The processing runs in your browser, so the recording is not uploaded, although the audio engine has to load first. For wider cleanup ideas there is the earlier post on removing hum from voice memos, and the audio tools category lists the other steps.

What does your recording space sound like most often: air conditioning, computer fans, traffic or something else? Tell us on the contact page.

Open Background Noise RemoverOpen Audio TrimmerOpen Audio Volume NormalizerOpen Extract Audio